High Nickel Alloy Titanium GX51 Plate Heat Exchanger Plate and Rubber Seal

Tranter GX51 Titanium Plate Heat Exchanger Plate for Water to Water Cooler High Quality

 

Plate Heat Exchanger Introduction

 

Plate Heat Exchangers were first produced in the 1920s and have since been widely used in a great number of sectors.

A plate exchanger consists of a series of parallel plates that are placed one above the other so as to allow the formation of a series of channels for fluids to flow between them.

The space between two adjacent plates forms the channel in which the fluid flows.

Inlet and outlet holes at the corners of the plates allow hot and cold fluids through alternating channels in the exchanger so that a plate is always in contact on one side with the hot fluid and the other with the cold.

The size of a plate can range from a few square centimeters (100mm * 300mm side) up to 2 or 3 square meters (1000mm * 2500mm side). The number of plates in a single exchanger ranges from just ten to several hundred, so reaching surface exchanger areas up to thousands of square meters.

Generally, these plates are corrugated in order to increase the turbulence, the thermal exchanger surface and to provide mechanical rigidity to the exchanger. Corrugation is achieved by cold forging of sheet metal with thicknesses of 0.3mm to 1mm.

The most frequently used materials for the plates are stainless steel (AISI 304, 316), titanium and aluminium.

The corrugation on the plates forces the fluid on a tortuous path, setting a space between two adjacent plates b, from 1 to 5 millimeters.

 

GX51 Model Plate Heat Exchanger Specification
 

Surface Area	0.51㎡
Plate Theta Angle	85 ° 115 °
Connection Diameter	145 mm
Plate Corrugate Thickness	3.25 mm
Plate Centre Length* Width	1143 * 300 mm
Plate Shape Length*Width	1354 * 507 mm

 

GX51 Plate Heat Exchanger Technical Information

 

 

Standard connection dimension	DN150
Tightening Bolt	M39
No. of long tightening bolts(TL)	4
No. of short tightening bolts (Ts)	4
Cover thickness	50 mm
Weight of guiding bar	11 kg/m
Weight of reinforced guiding bar	17 kg/m
Weight of tightening bolt	8.1 kg/m
A-dimension	3.8*n mm
C-dimension	LG+56 mm
F-dimension	LG+6 mm
Weight plate+gasket(W) AISI 304/316 0.5 mm                                          AISI 304/316 0.6 mm                                          Titanium 0.5 mm                                          Titanium 0.6 mm	2.55 kg  3.06 kg  1.57 kg  1.88 kg
Weight Frame	880+n*W kg

 

Max  No of plates	LT L	LG	C	F
48	500	600	656	606
60	750	600	656	606
88	750	1000	1056	1006
126	1050	1000	1056	1006
137	1050	1350	1406	1356
183	1350	1350	1406	1356
186	1350	1550	1606	1556
216	1650	1550	1606	1556
236	1650	1900	1956	1906
273	1950	1900	1956	1906
285	1950	2250	2306	2256
331	2250	2250	2306	2256
453	3000	3000	3056	3006
457	3000	-	-	-

 

LT L = Length long tightning bolt, based on 6.1 *n +210 mm

LG = Length guiding bar, based on 6.1 * n +230 mm

n= number of plates ( LG>2340 mm reinforced guiding bar Height +60mm; The reinforced guiding bar is not dimensioned for more plates.)

 

GX51 Plate Heat Exchanger Gasket & Plate Pictures

 

 

 

 

GX51 Ultraflex Plates

 

The plates are available with a herringbone pattern and either an acute or obtuse angle, making it possible to achieve six channel combinations.

 

The Ultraflex design allows two plates to be truned and rotated, giving six combinations of high and low theta plate pairs, matching the performance parameters of your application.

 

 

Ultraflex allows asymmetrical designs, with the primary and secondary circuits designed for heat transfer efficiency.

 

 

GX51 Gasket Choice

 

Glued Gaskets

M&C plate gaskets are specilly moulded elastomers to assure superior performance.

Numerous gasket materials - NBR, EPDM, Viton, Neoprene, Butyl.Hypalon, Teflon-encapsulated NBR and others - are available to match your process conditions, to maximum operating temperatures of 180℃.

 

Clip-on Gaskets

Consider the M&C Clip-on glueless gasket system wherever regular cleaning is necessary or aggressive fluids shorten gasket life. The unique design allows easy and fast clip-on installation for sure sealing and simple removal.

The clip-on is available in NBR and EPDM, both industrial and FDA ratings. These precision gaskets are moulded under rigorous manufacturing controls and are peroxide-cured for long life and excellent compression set resistance.

 

 

GX51 Plate Heat Exchanger Advantage with Shell- and -tube exchangers

 

Why fill up your engine room with heavy, bulky equipment, when efficiency and economy are vital factors?

 

A plate heat exchanger from M&C is only about 1/3 of the size and 1/6 of the weight of a shell- tube exchanger of comparable performance. Even if it  may seem reasonable to invest in a tube exchanger, this would have a much higher life cycle cost than a plate heat exchanger.

 

One reason is that the heat transfer properties of a plate heat exchanger are 3 to 5 times higher. Another is the close temperature approach which is as low as 1 ℃.

Efficiency pays off!

 

A plate heat exchanger offers many advantages compared with conventional shell-and-tube exchangers

• Up to 50% more efficient
• Up to 90% more compact
• 3-5 times higher k-values
• Unique turbulent flow design
• Closer temperature approach - as low as 1 ℃
• Far less material needed - less use of exotic alloys or titanium

Plate Heat Exchanger Advantage

• Much smaller footprints
• Lighter weight
• Easier installation
• Removable heat exchanger surfaces for effective cleaning
• Faster heating or cooling with less energy fluid
• Turbulent flow for better scaling resistance, greater reliablility
• Less steel, lower purchase price, shorter lead time and less expensive delivery

 

M&C Field Service

 

On- site services:

• Plate pack refurbishment( includes opening and closing of exchanger, pressure washing plates, visual plate inspection, checking and replacing gaskets as needed)
• Delivery and pick-up
• Plate pack exchanger
• Hydro/line testing of exchangers
• Troubleshooting

Operational help:

• Assustance with operational issues and maintenance training
• Help with design, testing, development and implementation of an effective preventative maintenance program
• Factory-backed engineering resources; including design, applications and materials

Warranty protection:

• One year on new parts; workmanship and lobor guaranteed.

 

Plate Heat Exchanger Pictures

 

 

M&C Heat Parts Company Profile

 

M&C Heat Parts Co., Ltd is founded in Wuxi, Jiangsu. M&C is specialized in designing and manufacturing high quality heat transfer equipment. The range of products comprises plates & gaskets, plate heat exchangers, gasketed heat exchangers and brazed heat exchangers. Thus, as one of the few producers worldwide, M&C offers solutions with optimum thermodynamic designs for different industries and virtually all applications.

M&C provide you with one-stop accessories service, multuple-brand & multiple model alternatives for your choice. We'll meet all your requirements of plate heat exchanger and keep your machine running contunously through our rich storage and quick response.

Moreover, we have a strict quality control and after-sales service system, from material purchasing to finished product package until the product received in good condition. Our products have been widely used all over the world in various fields.

 

 

 

M&C Plate Heat Exchanger Plates & Gaskets Other Models Recommend

 

Sondex/Danfoss - S4A, S7, S20, S21, S22, S41, S43, S47, S65, S81, S86, S100, S120, S130, SFD7, SFD13, SW19 and so on;

APV/SPX - H17, N25, N35, A055, A085, J060, J092, J107, M92, M107, K55, K71, B110, B134, P105, P190, SR1, SR2, TR9GN, TR9AL and so on;

Tranter/Swep - GX12, GL13, GC26, GC51, GX26, GX51, GX42, GX64, GX85, GX91, GX140, GX145 and so on;

API/Schmidt - Sigma 7, Sigma 9, Sigma 13, Sigma 26, Sigma 27, Sigma 36, Sigma 66, Sigma 106, Sigma 229, Sigma Star 45, Sigma Star 90 and so on;

Vicarb - V4, V13, V20, V28, V45, V60, V100, V110, V130 and so on;

Hisaka - EX11, EX15, EX15, LX026, LX195, LX395, LX595, RX135, RX395, RX595, UX115, UX225, UX395, UX495, UX815, UX995 and so on;

GEA - VT04, VT10, VT20, VT40, VT80, VT405, VT805, VT1306, NT50M, NT50X, NT100S, NT150S, NT150L, NT250M, NT250L and so on;

Funke - FP04, FP05, FP14, FP16, FP08, FP22, FP31, FP40, FP41, FP70, FP100, FP120 and so on;

Thermowave - TL200SS/PP, TL250SS/PP, TL400SS/PP. TL650SS/PP and so on;

DHP - DX143, DX146, DX20V, DX20DL, DX20DM, DX30S, DX36M and so on;

LHE - HT101, HT102, HT104, HT151, HT152, HT202, HT232, HT233 and so on;

 

M&C Plate Heat Exchanger Goods ready to Delivery